As Per the National Electrical Code, a cable tray system is "a unit or assembly of units or sections and associated fittings forming a rigid structural system used to securely fasten or support cables and raceways."
Raw Material | : | Hot Rolled MS Sheet / GI Sheet / Stainless Steel / Aluminium |
Finish Products | : | Pre Galvenised / Hot Dip Galvenised / Powder Coated |
Thikness | : | 1 mm to 2.5 mm |
Width | : | 50 mm To 1000 mm |
Height | : | 25mm To 150 mm |
Inner Flange | : | 12mm , 15mm, 20mm, 25mm |
Length | : | Standard Length 2500 mm / 3000 mm |
Remark | : | Tailor made sizes on specific request are available as per customer requirement |
Are mainly use in combination with perforated type of cable trays to route the cables in Various Degree where two wall are conjoining. Our product design allows the cable to route properly and bend take care of cable not to worn out, peel off or get damage while laying of cables.
Raw Material | ||
Hot Rolled M S Sheet | : | As per IS 1079/ 2062/5986/10748 |
Pre Galvenised Sheet | : | As per IS 277 |
Stainles Steel | : | AS per Grade 304/316 |
Aluminium | : | Commercial Grade |
Powder Coating | : | As per IS 101 |
Finish Products | ||
Zinc Coating | : | 465 Gms / Sq Mtr ( 65 Micorns ) |
710 Gms / Sq Mtr ( 75 Microns ) | ||
Tolerance | : | AS per IS 1852 |
Height | : | 25 mm to 150 mm |
Width | : | 50 mm to 1000 mm |
Inner Flange | : | 12 mm / 15mm / 25mm |
Radious | : | R300 / R600 / R900 / R1200 |
Degree | : | D45 /D60 / D90 |
Thikness | : | 1.2 mm / 1.6 mm / 2 mm / 2.5 mm |
SWG | : | 18 Swg / 16 swg / 14 swg / 12 swg |
Is suitable for joining cable trays in three different directions at Various Degree intervals in the same plane. Our product design allows the cable to route properly and bend take care of cable not to worn out, peel off or get damage while laying of cables.
Raw Material | ||
Hot Rolled M S Sheet | : | As per IS 1079/ 2062/5986/10748 |
Pre Galvenised Sheet | : | As per IS 277 |
Stainles Steel | : | AS per Grade 304/316 |
Aluminium | : | Commercial Grade |
Powder Coating | : | As per IS 101 |
Finish Products | ||
Zinc Coating | : | 465 Gms / Sq Mtr ( 65 Micorns ) |
710 Gms / Sq Mtr ( 75 Microns ) | ||
Tolerance | : | AS per IS 1852 |
Height | : | 25 mm to 150 mm |
Width | : | 50 mm to 1000 mm |
Inner Flange | : | 12 mm / 15mm / 25mm |
Radious | : | R300 / R600 / R900 / R1200 |
Degree | : | D45 /D60 / D90 |
Thikness | : | 1.2 mm / 1.6 mm / 2 mm / 2.5 mm |
SWG | : | 18 Swg / 16 swg / 14 swg / 12 swg |
Are mainly use for laying the cable horizontally which allows the cable to route from 4 end ,Our product design allows the cable to route properly and bend take care of cable not to worn out, peel off or get damage while laying of cables.
Raw Material | ||
Hot Rolled M S Sheet | : | As per IS 1079/ 2062/5986/10748 |
Pre Galvenised Sheet | : | As per IS 277 |
Stainles Steel | : | AS per Grade 304/316 |
Aluminium | : | Commercial Grade |
Powder Coating | : | As per IS 101 |
Finish Products | ||
Zinc Coating | : | 465 Gms / Sq Mtr ( 65 Micorns ) |
710 Gms / Sq Mtr ( 75 Microns ) | ||
Tolerance | : | AS per IS 1852 |
Height | : | 25 mm to 150 mm |
Width | : | 50 mm to 1000 mm |
Inner Flange | : | 12 mm / 15mm / 25mm |
Radious | : | R300 / R600 / R900 / R1200 |
Degree | : | D45 /D60 / D90 |
Thikness | : | 1.2 mm / 1.6 mm / 2 mm / 2.5 mm |
SWG | : | 18 Swg / 16 swg / 14 swg / 12 swg |
Are mainly used in combination with Perforated type of cable tray for joining cable trays of different widths in the same plane. Our product design allows the cable to route properly and bend take care of cable not to worn out, peel off or get damage while laying of cables.
Raw Material | ||
Hot Rolled M S Sheet | : | As per IS 1079/ 2062/5986/10748 |
Pre Galvenised Sheet | : | As per IS 277 |
Stainles Steel | : | AS per Grade 304/316 |
Aluminium | : | Commercial Grade |
Powder Coating | : | As per IS 101 |
Finish Products | ||
Zinc Coating | : | 465 Gms / Sq Mtr ( 65 Micorns ) |
710 Gms / Sq Mtr ( 75 Microns ) | ||
Tolerance | : | AS per IS 1852 |
Height | : | 25 mm to 150 mm |
Width | : | 50 mm to 1000 mm |
Inner Flange | : | 12 mm / 15mm / 25mm |
Radious | : | R300 / R600 / R900 / R1200 |
Degree | : | D45 /D60 / D90 |
Thikness | : | 1.2 mm / 1.6 mm / 2 mm / 2.5 mm |
SWG | : | 18 Swg / 16 swg / 14 swg / 12 swg |
Are mainly used in combination with Perforated type of cable tray for joining cable trays of different widths in the same plane. Our product design allows the cable to route properly and bend take care of cable not to worn out, peel off or get damage while laying of cables.
Raw Material | ||
Hot Rolled M S Sheet | : | As per IS 1079/ 2062/5986/10748 |
Pre Galvenised Sheet | : | As per IS 277 |
Stainles Steel | : | AS per Grade 304/316 |
Aluminium | : | Commercial Grade |
Powder Coating | : | As per IS 101 |
Finish Products | ||
Zinc Coating | : | 465 Gms / Sq Mtr ( 65 Micorns ) |
710 Gms / Sq Mtr ( 75 Microns ) | ||
Tolerance | : | AS per IS 1852 |
Height | : | 25 mm to 150 mm |
Width | : | 50 mm to 1000 mm |
Inner Flange | : | 12 mm / 15mm / 25mm |
Radious | : | R300 / R600 / R900 / R1200 |
Degree | : | D45 /D60 / D90 |
Thikness | : | 1.2 mm / 1.6 mm / 2 mm / 2.5 mm |
SWG | : | 18 Swg / 16 swg / 14 swg / 12 swg |
Are mainly use in combination with perforated type of cable trays to route. The cable where the direction changes to a different plane. Inside riser changes direction upward from the horizontal plane.
Our product design allows the cable to route properly and bend take care of cable not to worn out, peel off or get damage while laying of cables.
Raw Material | ||
Hot Rolled M S Sheet | : | As per IS 1079/ 2062/5986/10748 |
Pre Galvenised Sheet | : | As per IS 277 |
Stainles Steel | : | AS per Grade 304/316 |
Aluminium | : | Commercial Grade |
Powder Coating | : | As per IS 101 |
Finish Products | ||
Zinc Coating | : | 465 Gms / Sq Mtr ( 65 Micorns ) |
710 Gms / Sq Mtr ( 75 Microns ) | ||
Tolerance | : | AS per IS 1852 |
Height | : | 25 mm to 150 mm |
Width | : | 50 mm to 1000 mm |
Inner Flange | : | 12 mm / 15mm / 25mm |
Radious | : | R300 / R600 / R900 / R1200 |
Degree | : | D45 /D60 / D90 |
Thikness | : | 1.2 mm / 1.6 mm / 2 mm / 2.5 mm |
SWG | : | 18 Swg / 16 swg / 14 swg / 12 swg |
Are mainly use in combination with perforated type of cable trays to route. The cable where the direction changes to a different plane. Outside riser changes direction downward from the horizontal plane. Our product design allows the cable to route properly and bend take care of cable not to worn out, peel off or get damage while laying of cables.
Raw Material | ||
Hot Rolled M S Sheet | : | As per IS 1079/ 2062/5986/10748 |
Pre Galvenised Sheet | : | As per IS 277 |
Stainles Steel | : | AS per Grade 304/316 |
Aluminium | : | Commercial Grade |
Powder Coating | : | As per IS 101 |
Finish Products | ||
Zinc Coating | : | 465 Gms / Sq Mtr ( 65 Micorns ) |
710 Gms / Sq Mtr ( 75 Microns ) | ||
Tolerance | : | AS per IS 1852 |
Height | : | 25 mm to 150 mm |
Width | : | 50 mm to 1000 mm |
Inner Flange | : | 12 mm / 15mm / 25mm |
Radious | : | R300 / R600 / R900 / R1200 |
Degree | : | D45 /D60 / D90 |
Thikness | : | 1.2 mm / 1.6 mm / 2 mm / 2.5 mm |
SWG | : | 18 Swg / 16 swg / 14 swg / 12 swg |